Starter Kit STA-800

Product information "Starter Kit STA-800 "
  • Starter Kit with lococube® mini-PLC STG-800
  • Connection Cable VK-16 included (miCon-L)
  • Additional quick clamps for VDD, GND, CANH and CANL
  • Elegant board with four rubber feet
  • Removable from rugged plastic box
  • Mating connector for mini-PLC and quick clamps included
  • Ideal for training and experimental purposes
  • Dimensions (LxWxH): 120x116x40mm
  • Weight: 200g
Breadboard: yes
lococube® Box: yes
mini-PLC: STG-800

Customers also bought

lococube® mini-PLC STG-850
Tiny and super-flat CAN Logic ControllerHigh-Performance 32 Bit ARM® Cortex®6 analog Inputs 0 to 30 VDC, 12 bit ADC4 digital InputsEvent Counter Input 25 kHzPulse and Frequency Counter Input 40µs8 Solid-State Power Outputs up to 1.5 A1 Power PWM Output 16 Bit 1 Hz to 1 kHzCAN 2.0A/B InterfaceCANopen® and SAE J1939 Interface (no native miCon-L support!)IrDA/SIR InterfaceTTL-232 3.3V InterfaceComprehensive Fail Safe FunctionsIntuitive graphical Programming Capability with miCon-LOpen Source ‚C‘ Programming (Please note that the miCon-L firmware is irreversibly overwritten by “open source” programming and that we cannot release this firmware!)Compatible with PG-65 ProgrammerWide Operating Voltage Range 7 to 32 VDCWide Operating Temp. Range -40 to +70°CVibration resistant and rugged SealingCE, UL und ECE-R10 certifiedEngineered and manufactured in GermanyDimensions (LxWxH): 93x45x15mmWeight: 80g Manual STG-850 (EN) Programming Manual miCon-L (EN) Programming Manual KEIL® (EN) Sample Programs KEIL® for STG-850 3D-Data (PDF and STEP)

From €104.00*
lococube® mini-PLC STG-500
3 analog Inputs 0..30 VDC2 digital Inputs up to 1 kHz4 Power Outputs up to 1.5 A1 Power PWM Output 2 A/1..5 kHzReliable Solid-State OutputsProgrammable Status LEDRS232 Connection to PCIntegrated Temperature SensorIntuitive graphical Programming Capability (VK-10 + USB Adapter required)Wide Operating Voltage Range 7..32 VDCWide Operating Temp. Range -40..+70°CVibration resistant and rugged SealingVery low Current ConsumptionUniversal Aluminium Mounting PlateEngineered and manufactured in GermanyDimensions (LxWxH): 40x40x22mmWeight: 50 Manual STG-500 (EN) Drawing STG-500 3D-Data (PDF and STEP)

From €126.00*
lococube® CAN Display DMA-15
Tiny and compact CAN DisplayColor Touch TFT 2.4“ 240×320pWhite LED BacklightDesign Template Selection via CANNo Programming necessaryOpen Source Programming OptionCompatible with all CAN lococubes®´sFront IP65 Protection Grade (option)Panel-Mount without visible ScrewsPanel Cut-Out (LxW): 60 × 45 mmDimensions (LxW): 69 × 50 mmOperating Voltage 7 to 32 VDCEngineered and manufactured in Germany Manual DMA-15 (EN) Sample Programs miCon-L and KEIL® 3D-Data (PDF and STEP)

From €161.00*
Programmer ST-Link/V2 ISOL
For lococube® STG-8xx Open Source ProgrammingIntegrated opto-IsolationConnection Cable VK-35 is mandatory

€99.00*
Connection Cable VK-35
For lococube® Open Source Programming with ST-LinkSuitable for all STG-8xx and DMA-xxLength: 180 mm

€19.00*
Harness KS-85
You always get right down to business? No time to waste? We hear you! This harness lets you jump straight into development: Easily connect two BARTH-devices to each other and a power supply (sold seperately)CAN lines are properly terminated (60 Ohm) out of the box. The termination resistor can be unplugged easily & reversiblyClip-on connectors allow for easy connection of your own hardware, test equipment or another harness (KS-85 or other)

€69.00*